State Selection Commission (SSC JE)

AE Recruitment

SSC JE 2020 Notification out @_________________for recruitment of ____________ vacancies of Assistant Engineer Civil posts. Eligible candidates can register and fill SSC JE AEApplication Form for the SSC JE Recruitment 2020 from

SSC JE Recruitment 2020: Important Dates
Event Date
Release of SSC AE Notification 2020
Start Date of SSC Registration & Application Process Online
Last Date of SSC Registration Online
Last Date to pay application fee Online
Last Date of SSC Application Process Online
Last Date of receiving the Hard Copy & All Proof Documents though Speed Post/ Registered Post at SSC JE Registered Office
SSC AE Admit Card 2020
SSC AE Exam Date

Scheme of Examination :

The examination will consist of two papers. Paper-I is computer Based Examination and Paper-II is Conventional type. Detail of these papers will be as follows:-

Paper Mode of
Examination
Subject No of Questions Max Marks Duration Timings
1 Paper I (i) General Intelligence
Reasoning
(ii) General Awareness
(iii) Part A:
General Engineering
(Civil & Structural)
(OR)
Part B:
General Engineering (EE)
Part C:
General Engineering (ME)
50 50 Morning Shift
10am to 12 Noon
After Noon Shift
2pm to 4pm
Paper 2 Written Exam Part A:
General Engineering
(Civil & Structural)
(OR)
Part B:
General Engineering (Electrical)
Part C:
General Engineering (Mechanical
Part D:
General Engineering (Electronics)
300

2 Hours

Note: Entry to the examination venue will not be allowed after 9.30 AM in the morning shift and after 1.30 PM in the afternoon shift.

Junior Engineers ( Civil Mechanical, Electrical & Quantity Surveying & Contract Examination
Indicative Syllabus
The standard of the questions in Engineering subjects will be approximately of the level of Diploma in Engineering (Civil/ Electrical/ Mechanical/Electronics) from a recognized Institute, Board or University recognized by All India Board of Technical Education. All the questions will be set in SI units. The details of the syllabus are given below:

SSC JE Syllabus 2020:

 

 

f

Civil Syllabus

Paper 1:

(i) General Intelligence & Reasoning: The Syllabus for General Intelligence would include questions of both verbal and non-verbal type. The test may include questions on analogies, similarities, differences, space visualization, problem solving, analysis, judgement, decision making, visual memory, discrimination, observation, relationship concepts, arithmetical reasoning, verbal and figure classification, arithmetical number series etc. The test will also include questions designed to test the candidate’s abilities to deal with abstract ideas and symbols and their relationships, arithmetical computations and other analytical functions

(ii) General Awareness: Questions will be aimed at testing the candidate’s general awareness of the environment around him/her and its application to society.  Questions will also be designed to test knowledge of current events and of such matters of everyday observations and experience in their scientific aspect as may be expected of any educated person.  The test will also include questions relating to India and its neighbouring countries especially pertaining to History, Culture, Geography, Economic Scene, General Polity and Scientific Research, etc.  These questions will be such that they do not require a special study of any discipline.

(iii) General Engineering (Civil and Structural), (Electrical & Mechanical)

Paper 2: Part-A : 

Part-A : Civil  & Structural Engineering

Civil Engineering

Building Materials: Physical and Chemical properties, classification, standard tests, uses and manufacture/quarrying of materials e.g. building stones, silicate based materials, cement (Portland), asbestos products, timber and wood based products, laminates, bituminous materials, paints, varnishes.

Estimating, Costing and Valuation: estimate, glossary of technical terms, analysis of rates, methods and unit of measurement, Items of work – earthwork, Brick work (Modular & Traditional bricks), RCC work, Shuttering, Timber work, Painting, Flooring, Plastering.  Boundary wall, Brick building, Water Tank, Septic tank, Bar bending schedule, Centre line method, Mid-section formula, Trapezodial formula, Simpson’s rule.  Cost estimate of Septic tank, flexible pavements, Tube well, isolates and combined footings, Steel Truss, Piles and pile-caps.  Valuation – Value and cost, scrap value, salvage value, assessed value, sinking fund, depreciation and obsolescence, methods of valuation.

Surveying: Principles of surveying, measurement of distance, chain surveying, working of prismatic compass, compass traversing, bearings, local attraction, plane table surveying, theodolite traversing, adjustment of theodolite, Levelling, Definition of terms used in levelling, contouring, curvature and refraction corrections, temporary and permanent adjustments of dumpy level, methods of contouring, uses of contour map, tachometric survey, curve setting, earth work calculation, advanced surveying equipment.

Soil Mechanics: Origin of soil, phase diagram, Definitions-void ratio, porosity, degree of saturation, water content, specific gravity of soil grains, unit weights, density index and interrelationship of different parameters, Grain size distribution curves and their uses.  Index properties of soils, Atterberg’s limits, ISI soil classification and plasticity chart.  Permeability of soil, coefficient of permeability, determination of coefficient of permeability, Unconfined and confined aquifers, effective stress, quick sand, consolidation of soils, Principles of consolidation, degree of consolidation, pre-consolidation pressure, normally consolidated soil, e-log p curve, computation of ultimate settlement.  Shear strength of soils, direct shear test, Vane shear test, Triaxial test.  Soil compaction, Laboratory compaction test, Maximum dry density and optimum moisture content, earth pressure theories, active and passive earth pressures, Bearing capacity of soils, plate load test, standard penetration test.

Hydraulics: Fluid properties, hydrostatics, measurements of flow, Bernoulli’s theorem and its application, flow through pipes, flow in open channels, weirs, flumes, spillways, pumps and turbines.

Irrigation Engineering: Definition, necessity, benefits, 2II effects of irrigation, types and methods of irrigation, Hydrology – Measurement of rainfall, run off coefficient, rain gauge, losses from precipitation – evaporation, infiltration, etc.  Water requirement of crops, duty, delta and base period, Kharif and Rabi Crops, Command  area, Time factor, Crop ratio, Overlap allowance, Irrigation efficiencies.  Different type of canals, types of canal irrigation, loss of water in canals.  Canal lining – types and advantages.  Shallow and deep to wells, yield from a well.  Weir and barrage, Failure of weirs and permeable foundation, Slit and Scour, Kennedy’s theory of critical velocity.  Lacey’s theory of uniform flow.  Definition of flood, causes and effects, methods of flood control, water logging, preventive measure.  Land reclamation, Characteristics of affecting fertility of soils, purposes, methods, description of land and reclamation processes.  Major irrigation projects in India.

Transportation Engineering: Highway Engineering – cross sectional elements, geometric design, types of pavements, pavement materials – aggregates and bitumen, different tests, Design of flexible and rigid pavements – Water Bound Macadam (WBM) and Wet Mix Macadam (WMM), Gravel Road, Bituminous construction, Rigid pavement joint, pavement maintenance, Highway drainage, Railway Engineering- Components of permanent way – sleepers, ballast, fixtures and fastening, track geometry, points and crossings, track junction, stations and yards.  Traffic Engineering – Different traffic survey, speed-flow-density and their interrelationships, intersections and interchanges, traffic signals, traffic operation, traffic signs and markings, road safety.

Environmental Engineering: Quality of water, source of water supply, purification of water, distribution of water, need of sanitation, sewerage systems, circular sewer, oval sewer, sewer appurtenances, sewage treatments.  Surface water drainage.  Solid waste management – types, effects, engineered management system.  Air pollution – pollutants, causes, effects, control.  Noise pollution – cause, health effects, control.

Structural Engineering

Theory of structures: Elasticity constants, types of beams – determinate and indeterminate, bending moment and shear force diagrams of simply supported, cantilever and over hanging beams.  Moment of area and moment of inertia for rectangular & circular sections, bending moment and shear stress for tee, channel and compound sections, chimneys, dams and retaining walls, eccentric loads, slope deflection of simply supported and cantilever beams, critical load and columns, Torsion of circular section.

Concrete Technology: Properties, Advantages and uses of concrete, cement aggregates, importance of water quality, water cement ratio, workability, mix design, storage, batching, mixing, placement, compaction, finishing and curing of concrete, quality control of concrete, hot weather and cold weather concreting, repair and maintenance of concrete structures.

RCC Design: RCC beams-flexural strength, shear strength, bond strength, design of singly reinforced and double reinforced beams, cantilever beams.  T-beams, lintels.  One way and two way slabs, isolated footings.  Reinforced brick works, columns, staircases, retaining wall, water tanks (RCC design questions may be based on both Limit State and Working Stress methods).

Steel Design: Steel design and construction of steel columns, beams roof trusses plate girders

Mechanical Syllabus

Paper 1: General Intelligence & Reasoning: (i) General Intelligence & Reasoning: The Syllabus for General Intelligence would include questions of both verbal and non-verbal type. The test may include questions on analogies, similarities, differences, space visualization, problem solving, analysis, judgement, decision making, visual memory, discrimination, observation, relationship concepts, arithmetical reasoning, verbal and figure classification, arithmetical number series etc. The test will also include questions designed to test the candidate’s abilities to deal with abstract ideas and symbols and their relationships, arithmetical computations and other analytical functions.(ii) General Awareness: Questions will be aimed at testing the candidate’s general awareness of the environment around him/her and its application to society. Questions will also be designed to test knowledge of current events and of such matters of everyday observations and experience in their scientific aspect as may be expected of any educated person. The test will also include questions relating to India and its neighbouring countries especially pertaining to History, Culture, Geography, Economic Scene, General Polity and Scientific Research, etc. These questions will be such that they do not require a special study of any discipline.
(iii) General Engineering (Civil and Structural), (Electrical & Mechanical)
Paper II:

Theory of Machines and Machine Design : Concept of simple machine, Four bar linkage and link motion, Flywheels and fluctuation of energy, Power transmission by belts – V-belts and Flat belts, Clutches – Plate and Conical clutch, Gears – Type of gears, gear profile and gear ratio calculation, Governors – Principles and classification, Riveted joint, Cams, Bearings, Friction in collars and pivots.

Engineering Mechanics and Strength of Materials : Equilibrium of Forces, Law of motion, Friction, Concepts of stress and strain, Elastic limit and elastic constants, Bending moments and shear force diagram, Stress in composite bars, Torsion of circular shafts, Bucking of columns –Euler’s and Rankin’s theories, Thin walled pressure vessels.

Thermal Engineering : Properties of Pure Substances : p-v & P-T diagrams of pure substance like H2O, Introduction of steam table with respect to steam generation process; definition of saturation, wet & superheated status. Definition of dryness fraction of steam, degree of superheat of steam. H-s chart of steam (Mollier’s Chart).

1st Law of Thermodynamics: Definition of stored energy & internal energy, 1st Law of Thermodynamics of cyclic process, Non Flow Energy Equation, Flow Energy & Definition of Enthalpy, Conditions for Steady State Steady Flow; Steady State Steady Flow Energy Equation. 2nd Law of Thermodynamics : Definition of Sink, Source Reservoir of Heat, Heat Engine, Heat Pump & Refrigerator; Thermal Efficiency of Heat Engines & co-efficient of performance of Refrigerators, Kelvin – Planck & Clausius Statements of

2nd Law of Thermodynamics, Absolute or Thermodynamic Scale of temperature, Clausius Integral, Entropy, Entropy change calculation of ideal gas processes. Carnot Cycle & Carnot Efficiency, PMM-2; definition & its impossibility.

Air standard Cycles for IC engines: Otto cycle; plot on P-V, T-S Planes; Thermal Efficiency, Diesel Cycle; Plot on P-V, T-S planes; Thermal efficiency.

IC Engine Performance, IC Engine Combustion, IC Engine Cooling & Lubrication. Rankine cycle of steam : Simple Rankine cycle plot on P-V, T-S, h-s planes, Rankine cycle efficiency with & without pump work.

Boilers; Classification; Specification; Fittings & Accessories : Fire Tube & Water Tube Boilers. Air Compressors & their cycles; Refrigeration cycles; Principle of a Refrigeraton Plant; Nozzles & Steam Turbines

Fluid Mechanics & Machinery: Properties & Classification of Fluid : ideal & real fluids, Newton’s law of viscosity, Newtonian and Non-Newtonian fluids, compressible and in compressible fluids.>Fluid Statics : Pressure at a point.

Measurement of Fluid Pressure: Manometers, U-tube, Inclined tube.

Fluid Kinematics : Stream line, laminar & turbulent flow, external & internal flow, continuity equation.

Dynamics of ideal fluids: Bernoulli’s equation, Total head; Velocity head; Pressure head; Application of Bernoulli’s equitation.

Measurement of Flow rate Basic Principles : Venturimeter, Pilot tube, Orifice meter.

Hydraulic Turbines : Classifications, Principles.

Centrifugal Pumps : Classifications, Principles, Performance.

Production Engineering

Classification of Steel : mild steal & alloy steel, Heat treatment of steel, Welding – Arc Welding, Gas Welding, Resistance Welding, Special Welding Techniques i.e. TIG, MIG, etc. (Brazing & Soldering), Welding Defects & Testing; NDT, Foundry & Casting – methods, defects, different casting processes,
Forging, Extrusion, etc, Metal cutting principles, cutting tools, Basic Principles of machining with (i) Lathe (ii) Milling (iii) Drilling (iv) Shaping (v) Grinding, Machines, tools & manufacturing processes.

 

SSC JE Important Links:

SSC – JE – 2020 – Syllabus Mechanical : PDF Download SSC JE Mechanical Detailed Syllabus 2020

For Further Details Connect to SSC JE Website @ _______________________________.

For SSC – JE – 2020 Notification link________________________________.